本文另有中文版。
What luggage fabric usually has to survive is not merely being coated, but remaining water-resistant, resistant to hydrostatic pressure, ageing and abrasion, and easy to clean after soiling. Wuxi Qianzhou Xinghua Machinery Co., Ltd. publishes a dedicated luggage-fabric coating machine page for this process. The official description names oxford and similar luggage fabrics, with padding and coating as the process, and with the functions listed above.
The public platform is the same family as the textile coating machine, given as TC-180-420. Nominal width is 1,800–4,200 mm (180–420 cm); mechanical speed 5–65 m/min, typical running speed 30–40 m/min; the heat source may be thermal oil, gas or steam, with a published configuration share of thermal oil 90%, gas 5% and steam 5%. The oven is configured to the customer’s requirements. The official pages also give a way of reading those figures: a mechanical speed limit is not the process speed at which a given fabric and paste will run stably, and a special-purpose machine should not be assumed to cover every width band of a multi-purpose line. Proposal parameters are locked at enquiry against samples and required output.
Padding is more common on luggage fabric because the process often needs the paste to penetrate, rather than only to form a surface film. The official coating process is written as infeed, then padding or knife application, then drying and setting. Coating heads on the textile-coating page are listed as padding, knife or combination heads, locked in the quotation. When the coating or the coat weight changes, the combination coating head for a coating machine (CN205995709U) is written as a change of head, not a dismantling of the machine.
Whether the coat weight is even still depends first on whether the gap can be held to a set value. Electro-hydraulic servo control (CN206111703U) is directed at set-value control in the coating process, rather than at chasing the result with a hand-wheel. The combination infeed frame (CN205995743U) and the temperature-controlled infeed frame (CN205995744U) deal with the selvedge and infeed temperature before the web reaches the head. Those published patents are product-level evidence that can be checked; the “119 patents” figure on the official site is a company total and also includes carpet and flocking equipment, so it should not be used on its own to prove this luggage-fabric machine.
Why a configuration can be discussed against a customer’s fabric, rather than chosen only from a standard machine on the floor, is set out in the official manufacturing description: cold-working, sheet-metal, machining, final-assembly, electrical and warehouse workshops share one site; key rollers, frames, housings, oven structures, outer panels and air ducts are processed in-house; and complete machines are trial-run before shipment. That is not a claim that every component is made in the plant. It is a statement that key structures such as rollers and frames can be machined in-house to the order.
The predecessor factory started in 1993; the limited company was established in 2003 under the business license. The plant is at No. 3 Longtan Road, Qianzhou Supporting Area, Huishan Economic Development Zone, Wuxi, Jiangsu. The company is a national high-tech enterprise; the current certificate, number GR202532008525, was issued on 19 December 2025 and is valid for three years. ISO 9001 certificate 54326Q00104R253 covers “manufacture of textile finishing equipment and carpet finishing equipment” and is valid until 29 September 2029.
Commercial terms published on the official about page are: a typical lead time of about three months, or about four months for special models; 30% deposit, with the balance paid before shipment; sea or land freight; a one-year warranty; on-site installation and commissioning, with staff available to travel overseas; and lifetime after-sales support. The trial run after installation takes place at the customer’s plant. Lead time and configuration for a given order remain subject to the factory quotation.
The company will attend ITMA ASIA + CITME 2026 in Shanghai, 20–24 November, booth H8.1-D11. Enquiries: 0510-83397635 / 0510-83382635, info@xhmachinery.com. See also the contact page.